In May 2026, a Victorian coroner released findings into three house fires that killed four people in Lara, Sunshine West and St Albans. In every one of those homes, something had gone wrong with the smoke alarms. An alarm more than ten years old with a dead battery. Batteries that were never changed. No evidence of alarms at all.

None of those failures were dramatic. That's what makes them hard to read. They're the kind of thing most of us mean to check and never quite get around to.
Three Dates Split Melbourne Homes Into Groups
The smoke alarm requirements in Victoria hinge on when your home was built, largely renovated or extended. Homes from before 1 August 1997 can legally use stand-alone 9 volt battery alarms. After that date, the law calls for hardwired smoke alarms connected to 240 volt mains power with a backup battery.
A third date matters too. Homes built or significantly renovated after 1 May 2014 that need more than one alarm must have them interconnected, so they all sound together when one is triggered.
Every home also needs at least one alarm on each level, placed between the sleeping areas and the rest of the house. That's the legal minimum, and fire services are clear that it's only a starting point.
A Big Renovation Can Pull You Into Newer Rules
This catches people out. The rules don't just follow the year on the original plans. A major renovation or extension can bring an older home under the newer requirements, which can mean hardwiring and interconnection where battery alarms were fine before.
If you're adding a bedroom, knocking out walls or extending at the back, ask your builder or electrician about the alarms early, before the plaster goes up. Running cable through an open ceiling is far easier than doing it afterwards.
Rentals Picked Up a New Annual Test
Since November 2025, rental providers must make sure smoke alarms in every residential rental are tested at least once every 12 months. A faulty smoke alarm also counts as an urgent repair. For landlords with a few properties around Melbourne's west, that test is now a fixed job on the calendar, not a nice-to-have.
Victoria May Be Heading Queensland's Way
The coroner's single recommendation asked the Minister for Housing and Building to consider Fire Rescue Victoria's proposal to strengthen the rules along Queensland's lines. Queensland's reforms require every home, however old, to have alarms that are hardwired or run on a non-removable 10-year battery, sit in every bedroom and hallway on every level, are interconnected and are less than 10 years old.
Nothing has changed in Victorian law yet. But the direction is hard to miss, and homeowners who upgrade now won't be scrambling later.
What It Usually Costs
A Victorian Government guide from May 2026 gives a rough idea of prices.
- 9 volt battery alarms from about $10 each, with a battery swap every year.
- Sealed 10-year battery alarms from about $20 each.
- Wireless interconnected alarms with a 10-year battery from about $45 each.
- Hardwired work by an electrician often $160 to $350 or more per alarm, depending on wiring and access.
Those are indicative figures only, and every house is different. Still, for most homes, proper smoke alarm installation in Melbourne costs less than people expect, especially when it's done in one visit. Fire services also recommend smoke alarm replacement every 10 years, mains-powered units included, so an old alarm that still beeps when tested may still be due.
Licensed Hands for Anything on 240 Volts
Battery alarms are a simple DIY job. Anything wired into mains power should be done by a licensed electrician. AAA Electrical and Solar's in-house electricians can replace ageing units, add alarms to bedrooms and set up interconnected smoke alarms across the home, hardwired or wireless depending on what the house allows.
Check the Date on the Back
Tonight, take one alarm down and turn it over. There's usually a manufacture date printed on the back. If it's more than ten years old, you already know what to do next. It's a small, slightly boring job. It's also the one that matters most at three in the morning.
Small Detail That Leaves Your Smoke Alarm Useless
Victoria's smoke alarm rules depend on when your home was built or renovated, and a coroner has now asked the state to go much further. Here is what applies to your home today, what it costs to get right and what may be coming next.
In May 2026, a Victorian coroner released findings into three house fires that killed four people in Lara, Sunshine West and St Albans. In every one of those homes, something had gone wrong with the smoke alarms. An alarm more than ten years old with a dead battery. Batteries that were never changed. No evidence of alarms at all.
None of those failures were dramatic. That's what makes them hard to read. They're the kind of thing most of us mean to check and never quite get around to.
Three Dates Split Melbourne Homes Into Groups
The smoke alarm requirements in Victoria hinge on when your home was built, largely renovated or extended. Homes from before 1 August 1997 can legally use stand-alone 9 volt battery alarms. After that date, the law calls for hardwired smoke alarms connected to 240 volt mains power with a backup battery.
A third date matters too. Homes built or significantly renovated after 1 May 2014 that need more than one alarm must have them interconnected, so they all sound together when one is triggered.
Every home also needs at least one alarm on each level, placed between the sleeping areas and the rest of the house. That's the legal minimum, and fire services are clear that it's only a starting point.
A Big Renovation Can Pull You Into Newer Rules
This catches people out. The rules don't just follow the year on the original plans. A major renovation or extension can bring an older home under the newer requirements, which can mean hardwiring and interconnection where battery alarms were fine before.
If you're adding a bedroom, knocking out walls or extending at the back, ask your builder or electrician about the alarms early, before the plaster goes up. Running cable through an open ceiling is far easier than doing it afterwards.
Rentals Picked Up a New Annual Test
Since November 2025, rental providers must make sure smoke alarms in every residential rental are tested at least once every 12 months. A faulty smoke alarm also counts as an urgent repair. For landlords with a few properties around Melbourne's west, that test is now a fixed job on the calendar, not a nice-to-have.
Victoria May Be Heading Queensland's Way
The coroner's single recommendation asked the Minister for Housing and Building to consider Fire Rescue Victoria's proposal to strengthen the rules along Queensland's lines. Queensland's reforms require every home, however old, to have alarms that are hardwired or run on a non-removable 10-year battery, sit in every bedroom and hallway on every level, are interconnected and are less than 10 years old.
Nothing has changed in Victorian law yet. But the direction is hard to miss, and homeowners who upgrade now won't be scrambling later.
What It Usually Costs
A Victorian Government guide from May 2026 gives a rough idea of prices.
- 9 volt battery alarms from about $10 each, with a battery swap every year.
- Sealed 10-year battery alarms from about $20 each.
- Wireless interconnected alarms with a 10-year battery from about $45 each.
- Hardwired work by an electrician often $160 to $350 or more per alarm, depending on wiring and access.
Those are indicative figures only, and every house is different. Still, for most homes, proper smoke alarm installation in Melbourne costs less than people expect, especially when it's done in one visit. Fire services also recommend smoke alarm replacement every 10 years, mains-powered units included, so an old alarm that still beeps when tested may still be due.
Licensed Hands for Anything on 240 Volts
Battery alarms are a simple DIY job. Anything wired into mains power should be done by a licensed electrician. AAA Electrical and Solar's in-house electricians can replace ageing units, add alarms to bedrooms and set up interconnected smoke alarms across the home, hardwired or wireless depending on what the house allows.
Check the Date on the Back
Tonight, take one alarm down and turn it over. There's usually a manufacture date printed on the back. If it's more than ten years old, you already know what to do next. It's a small, slightly boring job. It's also the one that matters most at three in the morning.
Small Detail That Leaves Your Smoke Alarm Useless
Victoria's smoke alarm rules depend on when your home was built or renovated, and a coroner has now asked the state to go much further. Here is what applies to your home today, what it costs to get right and what may be coming next.
In May 2026, a Victorian coroner released findings into three house fires that killed four people in Lara, Sunshine West and St Albans. In every one of those homes, something had gone wrong with the smoke alarms. An alarm more than ten years old with a dead battery. Batteries that were never changed. No evidence of alarms at all.
None of those failures were dramatic. That's what makes them hard to read. They're the kind of thing most of us mean to check and never quite get around to.
Three Dates Split Melbourne Homes Into Groups
The smoke alarm requirements in Victoria hinge on when your home was built, largely renovated or extended. Homes from before 1 August 1997 can legally use stand-alone 9 volt battery alarms. After that date, the law calls for hardwired smoke alarms connected to 240 volt mains power with a backup battery.
A third date matters too. Homes built or significantly renovated after 1 May 2014 that need more than one alarm must have them interconnected, so they all sound together when one is triggered.
Every home also needs at least one alarm on each level, placed between the sleeping areas and the rest of the house. That's the legal minimum, and fire services are clear that it's only a starting point.
A Big Renovation Can Pull You Into Newer Rules
This catches people out. The rules don't just follow the year on the original plans. A major renovation or extension can bring an older home under the newer requirements, which can mean hardwiring and interconnection where battery alarms were fine before.
If you're adding a bedroom, knocking out walls or extending at the back, ask your builder or electrician about the alarms early, before the plaster goes up. Running cable through an open ceiling is far easier than doing it afterwards.
Rentals Picked Up a New Annual Test
Since November 2025, rental providers must make sure smoke alarms in every residential rental are tested at least once every 12 months. A faulty smoke alarm also counts as an urgent repair. For landlords with a few properties around Melbourne's west, that test is now a fixed job on the calendar, not a nice-to-have.
Victoria May Be Heading Queensland's Way
The coroner's single recommendation asked the Minister for Housing and Building to consider Fire Rescue Victoria's proposal to strengthen the rules along Queensland's lines. Queensland's reforms require every home, however old, to have alarms that are hardwired or run on a non-removable 10-year battery, sit in every bedroom and hallway on every level, are interconnected and are less than 10 years old.
Nothing has changed in Victorian law yet. But the direction is hard to miss, and homeowners who upgrade now won't be scrambling later.
What It Usually Costs
A Victorian Government guide from May 2026 gives a rough idea of prices.
- 9 volt battery alarms from about $10 each, with a battery swap every year.
- Sealed 10-year battery alarms from about $20 each.
- Wireless interconnected alarms with a 10-year battery from about $45 each.
- Hardwired work by an electrician often $160 to $350 or more per alarm, depending on wiring and access.
Those are indicative figures only, and every house is different. Still, for most homes, proper smoke alarm installation in Melbourne costs less than people expect, especially when it's done in one visit. Fire services also recommend smoke alarm replacement every 10 years, mains-powered units included, so an old alarm that still beeps when tested may still be due.
Licensed Hands for Anything on 240 Volts
Battery alarms are a simple DIY job. Anything wired into mains power should be done by a licensed electrician. AAA Electrical and Solar's in-house electricians can replace ageing units, add alarms to bedrooms and set up interconnected smoke alarms across the home, hardwired or wireless depending on what the house allows.
Check the Date on the Back
Tonight, take one alarm down and turn it over. There's usually a manufacture date printed on the back. If it's more than ten years old, you already know what to do next. It's a small, slightly boring job. It's also the one that matters most at three in the morning.
Small Detail That Leaves Your Smoke Alarm Useless
Victoria's smoke alarm rules depend on when your home was built or renovated, and a coroner has now asked the state to go much further. Here is what applies to your home today, what it costs to get right and what may be coming next.
In May 2026, a Victorian coroner released findings into three house fires that killed four people in Lara, Sunshine West and St Albans. In every one of those homes, something had gone wrong with the smoke alarms. An alarm more than ten years old with a dead battery. Batteries that were never changed. No evidence of alarms at all.
None of those failures were dramatic. That's what makes them hard to read. They're the kind of thing most of us mean to check and never quite get around to.
Three Dates Split Melbourne Homes Into Groups
The smoke alarm requirements in Victoria hinge on when your home was built, largely renovated or extended. Homes from before 1 August 1997 can legally use stand-alone 9 volt battery alarms. After that date, the law calls for hardwired smoke alarms connected to 240 volt mains power with a backup battery.
A third date matters too. Homes built or significantly renovated after 1 May 2014 that need more than one alarm must have them interconnected, so they all sound together when one is triggered.
Every home also needs at least one alarm on each level, placed between the sleeping areas and the rest of the house. That's the legal minimum, and fire services are clear that it's only a starting point.
A Big Renovation Can Pull You Into Newer Rules
This catches people out. The rules don't just follow the year on the original plans. A major renovation or extension can bring an older home under the newer requirements, which can mean hardwiring and interconnection where battery alarms were fine before.
If you're adding a bedroom, knocking out walls or extending at the back, ask your builder or electrician about the alarms early, before the plaster goes up. Running cable through an open ceiling is far easier than doing it afterwards.
Rentals Picked Up a New Annual Test
Since November 2025, rental providers must make sure smoke alarms in every residential rental are tested at least once every 12 months. A faulty smoke alarm also counts as an urgent repair. For landlords with a few properties around Melbourne's west, that test is now a fixed job on the calendar, not a nice-to-have.
Victoria May Be Heading Queensland's Way
The coroner's single recommendation asked the Minister for Housing and Building to consider Fire Rescue Victoria's proposal to strengthen the rules along Queensland's lines. Queensland's reforms require every home, however old, to have alarms that are hardwired or run on a non-removable 10-year battery, sit in every bedroom and hallway on every level, are interconnected and are less than 10 years old.
Nothing has changed in Victorian law yet. But the direction is hard to miss, and homeowners who upgrade now won't be scrambling later.
What It Usually Costs
A Victorian Government guide from May 2026 gives a rough idea of prices.
- 9 volt battery alarms from about $10 each, with a battery swap every year.
- Sealed 10-year battery alarms from about $20 each.
- Wireless interconnected alarms with a 10-year battery from about $45 each.
- Hardwired work by an electrician often $160 to $350 or more per alarm, depending on wiring and access.
Those are indicative figures only, and every house is different. Still, for most homes, proper smoke alarm installation in Melbourne costs less than people expect, especially when it's done in one visit. Fire services also recommend smoke alarm replacement every 10 years, mains-powered units included, so an old alarm that still beeps when tested may still be due.
Licensed Hands for Anything on 240 Volts
Battery alarms are a simple DIY job. Anything wired into mains power should be done by a licensed electrician. AAA Electrical and Solar's in-house electricians can replace ageing units, add alarms to bedrooms and set up interconnected smoke alarms across the home, hardwired or wireless depending on what the house allows.
Check the Date on the Back
Tonight, take one alarm down and turn it over. There's usually a manufacture date printed on the back. If it's more than ten years old, you already know what to do next. It's a small, slightly boring job. It's also the one that matters most at three in the morning.
Small Detail That Leaves Your Smoke Alarm Useless
Victoria's smoke alarm rules depend on when your home was built or renovated, and a coroner has now asked the state to go much further. Here is what applies to your home today, what it costs to get right and what may be coming next.
In May 2026, a Victorian coroner released findings into three house fires that killed four people in Lara, Sunshine West and St Albans. In every one of those homes, something had gone wrong with the smoke alarms. An alarm more than ten years old with a dead battery. Batteries that were never changed. No evidence of alarms at all.
None of those failures were dramatic. That's what makes them hard to read. They're the kind of thing most of us mean to check and never quite get around to.
Three Dates Split Melbourne Homes Into Groups
The smoke alarm requirements in Victoria hinge on when your home was built, largely renovated or extended. Homes from before 1 August 1997 can legally use stand-alone 9 volt battery alarms. After that date, the law calls for hardwired smoke alarms connected to 240 volt mains power with a backup battery.
A third date matters too. Homes built or significantly renovated after 1 May 2014 that need more than one alarm must have them interconnected, so they all sound together when one is triggered.
Every home also needs at least one alarm on each level, placed between the sleeping areas and the rest of the house. That's the legal minimum, and fire services are clear that it's only a starting point.
A Big Renovation Can Pull You Into Newer Rules
This catches people out. The rules don't just follow the year on the original plans. A major renovation or extension can bring an older home under the newer requirements, which can mean hardwiring and interconnection where battery alarms were fine before.
If you're adding a bedroom, knocking out walls or extending at the back, ask your builder or electrician about the alarms early, before the plaster goes up. Running cable through an open ceiling is far easier than doing it afterwards.
Rentals Picked Up a New Annual Test
Since November 2025, rental providers must make sure smoke alarms in every residential rental are tested at least once every 12 months. A faulty smoke alarm also counts as an urgent repair. For landlords with a few properties around Melbourne's west, that test is now a fixed job on the calendar, not a nice-to-have.
Victoria May Be Heading Queensland's Way
The coroner's single recommendation asked the Minister for Housing and Building to consider Fire Rescue Victoria's proposal to strengthen the rules along Queensland's lines. Queensland's reforms require every home, however old, to have alarms that are hardwired or run on a non-removable 10-year battery, sit in every bedroom and hallway on every level, are interconnected and are less than 10 years old.
Nothing has changed in Victorian law yet. But the direction is hard to miss, and homeowners who upgrade now won't be scrambling later.
What It Usually Costs
A Victorian Government guide from May 2026 gives a rough idea of prices.
- 9 volt battery alarms from about $10 each, with a battery swap every year.
- Sealed 10-year battery alarms from about $20 each.
- Wireless interconnected alarms with a 10-year battery from about $45 each.
- Hardwired work by an electrician often $160 to $350 or more per alarm, depending on wiring and access.
Those are indicative figures only, and every house is different. Still, for most homes, proper smoke alarm installation in Melbourne costs less than people expect, especially when it's done in one visit. Fire services also recommend smoke alarm replacement every 10 years, mains-powered units included, so an old alarm that still beeps when tested may still be due.
Licensed Hands for Anything on 240 Volts
Battery alarms are a simple DIY job. Anything wired into mains power should be done by a licensed electrician. AAA Electrical and Solar's in-house electricians can replace ageing units, add alarms to bedrooms and set up interconnected smoke alarms across the home, hardwired or wireless depending on what the house allows.
Check the Date on the Back
Tonight, take one alarm down and turn it over. There's usually a manufacture date printed on the back. If it's more than ten years old, you already know what to do next. It's a small, slightly boring job. It's also the one that matters most at three in the morning.
Comments (0)
Want to join the discussion?
Log In to Comment